P.O. Box 540 Westtown, PA 19395 Phone 610-696-9220  Fax 610-344-7519  lba@ncroll.com
LINN BROWN AND ASSOCIATES, INC. (LB&A) manufactures and supplies a variety of non-conductive pipe rollers,  pipe hangers, and pipeline bridge crossing products and supports.   Please contact us to place an order or if you would like to receive our free catalogue.

 LIST OF ALL PRODUCTS

ADJUSTABLE ROLL GUIDE (3B)

TABLE OF DIMENSIONS

COLOR DRAWINGS WITH USE RECOMMENDATIONS

Adjustable Roll Guide (3B) with Non-Conductive Roller and FRP 180 Saddle

Adjustable Roll Guide Support Includes:

  • 4 Adjustable Sockets

  • 2 Roll Axles

  • 2 Vertical Threaded Rods

  • 12 Hex Nuts

ADJUSTABLE ROLL GUIDE (3B)

TABLE OF DIMENSIONS

Measurements in inches unless otherwise noted.

PIPE SIZE

 A B C ROD SIZE D E SOCKET NO. MAX LOAD LBS. WT. LBS./EA.

2

1 9/16

4 1/8

3/8

3/8

12

#1-3/8

600

2.15

2 1/2

1 7/8

5 1/4

1/2

1/2

14

#2-1/2

660

4.02

3

2 3/16

5 11/16

1/2

1/2

14

#2-1/2

700

4.34

3 1/2

2 1/2

6 3/16

1/2

1/2

14

#2-1/2

750

4.48

4

2 3/4

7

1/2

5/8

18

#3-1/2

750

6.73

5

3 7/16

8 1/8

5/8

5/8

18

#3-5/8

750

8.95

6

4

9 11/16

3/4

3/4

24

#4-3/4

1070

14.59

8

5 1/4

12 1/8

7/8

7/8

24

#5-7/8

1350

24.33

10

6 1/4

14 1/8

7/8

7/8

30

#5-7/8

1730

27.7

12

7 7/16

16

1

7/8

30

#5-1

2400

39.62

14

8 5/16

17 7/8

1 1/8

1

36

#6-1 1/8

3130

57.61

16

9 3/8

20 1/8

1 1/4

1

36

#6-1 1/4

3970

87.57

18

10 3/8

22 1/8

1 1/4

1 

42

#7-1 1/4

4200

99.54

20

11 1/2

24 3/8

1 1/4

1 1/4

42

#8-1 1/4

4550

131.82

24

13 13/16

28 5/8

1 1/2

1 1/2

42

#9-1 1/2

6160

219.74

 

ADJUSTABLE ROLL GUIDE (3B)

DRAWINGS AND RECOMMENDATIONS

PAINTED OR BARE STEEL PIPE

RECOMMENDATION:

  • NON-CONDUCTIVE PIPE ROLLER

Non-Conductive Rollers should be used in lieu of, or as a direct replacement for, cast iron rolls on any bridge main installation that is, or is going to be, painted. This applies for both existing and new mains. Most paints provide only a thin barrier and are extremely susceptible to abrasion damage. This is particularly true at each pipe to support contact.

REASONS:

  • ELIMINATES THE POSSIBILITY OF MOISTURE ENTRAPMENT.

  • ROLLER WILL NOT BIND OR ABRADE THE PAINT.

  • MAINTAINS ELECTRICAL ISOLATION.

The polyurethane based Non-Conductive Rollers are best used alone with thin coatings because they are non-abrasive and maintain a minimum surface contact. This eliminates any possibility of moisture collecting between pipe and support. In addition, the Non-Conductive Rollers are solid and do not have the same tendency to bind as the hollow cast iron rolls. Lubricating the roller’s stainless steel sleeve prior to inserting the axle seals out moisture and reduces friction.

When a pipe has a thin barrier coating the use of a FRP Shield increases the possibility of moisture entrapment between the pipe and shield interface. In most cases this would aggravate any corrosive conditions located between the pipe and FRP Shield.

TAPE COATED PIPE WITH CAST IRON ROLLER

RECOMMENDATION:

  • FRP TYPE # 180 SADDLES

Type# 180 Saddles needs to be installed with any factory or field applied tape. This is particularly important when cast iron rolls are used. The profile of cast iron rolls do not accommodate thick barrier coatings. The tapes change the OD of the pipe to the point it will no longer rest in the cradle of the roll as is the case with bare or painted pipes. Instead, the pipe will rest on the peaks of the roll. This situation aggravates the point loading that normally occurs at each of the pipe’s supports.

REASONS:

  • PROTECTS THE TAPE FROM ABRASION.

  • PREVENTS COLD FLOW OF THE TAPE.

  • ENSURES ELECTRICAL ISOLATION.

Tape wraps are thick barrier coating that must be protected at each support. Without protection the tape will cold flow as a result of being sandwiched between the pipe and its support. Abrasion due to even minor thermal expansion and contraction will further compromise the integrity of the tape. Fiberglass reinforcement enables the FRP Saddles to tolerate the point loading and prevent abrasion damage by providing a desirable weight distribution. The FRP Saddles also ensure a high degree of electrical isolation.Unlike non-reinforced plastics, the Fiberglass Reinforced Saddles do not get brittle in the cold and are resistant to UV degradation.

TAPE COATED PIPE WITH NON-CONDUCTIVE ROLLER

RECOMMENDATION:

  • FRP TYPE # 180 SADDLES & NON-CONDUCTIVE ROLLER

Type # 180 Saddles need to be installed with any factory or field applied tape. This is the case even when Non-Conductive Rollers are used. The profile of a urethane roller is designed to accommodate both the tape wrap and FRP Saddles. Although the Non-Conductive Rollers greatly reduce the possibility of abrasion, the tape must still be protected from cold flow damage. FRP Saddles prevent damage by providing the necessary weight distribution between the pipe and its support. This is particularly important if the pipe becomes misaligned.

REASONS:

  • PROTECTS THE TAPE FROM ABRASION.

  • PREVENTS COLD FLOW OF THE TAPE.

  • ENSURES ELECTRICAL ISOLATION.

When used together, the Non-Conductive Rollers and FRP Saddles provide the best possible protection for any tape type wrap. Unlike hollow cast iron rolls, the Non-Conductive Rollers are solid and do not tend to bind and will not corrode internally. The urethane composition stays flexible even in cold temperatures. This provides a degree of vibration tolerance which one of the primary causes for alignment problems. Lubricating the roller’s stainless steel sleeve seals out moisture and reduces friction. FRP Saddles maintain the tape’s integrity against both normal and possible abnormal loading due to misalignments and/or support failure.

Back to LB&A Home Page

Copyright © 2007 LB&A Inc.